Release Alpha Zen Protocol 215+ Acorn Miner (Solo)

Mubarak1961

Newcomer
Member
Joined
Dec 27, 2018
Messages
8
Likes
0
#76
It does not matter what settings you put on your 1080 card they don't affect anything to do with the acorn. If you want to up the setting on the acorn you just hold shift and the plus button on your keyboard. While being in the command prompt of the acorn. There is no GPU boost right now so your card and your Acorn are working separately
You are absolutely right , beside I just post my setting to tell that I am not overheating my system. and I new that Acorn card dose not coupling right nom with the GPU, we are in testing phase to make sure the new acorn work and feedback any issue help the developers to solve , so they produce SQUL Miner free of errors
 

DragonLogic

Newcomer
Member
Joined
Dec 6, 2018
Messages
4
Likes
0
#77
Cheers, I'll try reseating the Acorn. The thing is that even if I run the Acorn at 0.95 v and 390mhs which runs stable for days the invalid shares are almost exactly the same percentage. Is there a possibility that the firmware for the FPGA is corrupt? Will reflashing it help?

I/ACORNMINER: A-1(471e0200): Temp: 65.34 C, VCCINT: 0.94 V, Shares(F/A/I/R/L): 50305/13009/24426/21/12849, Clk: 195.00 MHz, Core Hashrate: 390.00 MH/s
I/ACORNMINER: Total Hashrate: 390.00 MH/s

I left it running for days and there are no crashes on the pool I'm averaging 182mhs.
I'm only running 1 Acorn on the systems that I've tried Acorns on. I have unplugged all risers and had just the Acorn running on it's own on 3 systems now. I tried a different address and pool same problem.

Things I tried are:

The Acorn has been tested on a different motherboard this time a Celeron 1840t, MSI gaming 5 z97, 8gb 1333 ram, 2x 120sata drives 7 RX Vega 56 MSI airboost gcards, usually mining Ethereum, Monero or other cryptonote based algos.
on this system the problem is much worse I hardly get any valid shares if I adjust the clock speed (note the results are slightly better if I don't touch the speed + or - and no matter what speed I run the Acorn at the voltage never goes above 0.97v even at 100 MHz or lower. Using the default in the batch file it starts mining at 0.86v bear in mind that this a different PSU. It leads me to think there maybe a problem with the VRM on the Acorn as the voltages are all over the place for the Acorn on this system. I hooked up a power meter to the PSU to see if it was overloaded I'm drawing 1387w average when mining Ethereum with the acorn running 1455w when mining Monero. The power supply is 2000w on the 12v rail 100w on the 3.3v rail and 100w combined on all the other rails that said it's overall rating is 2000w. If I run the Acorn without any other programs running the power draw is 312w on the whole system but the voltage is still low on the Acorn.
I changed the PSU to 2x Antec HCP1300 PSU same problem although the voltages where higher but still with invalid shares.


C:\Users\Dragon Logic\Desktop\AcornMinerWin_Alpha_012c (1)>AcornMiner.exe us.zenprotocolpool.com 8811 zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss Miner01 not posting my email address @ online 175
I/ACORNMINER: Started Winsock!
I/LOGGER: Log level set to Info
I/ACORNMINER: Starting AcornMiner v0.12c
I/ACORNMINER: Scanning for Acorns...
I/ACORNMINER: Found 1 SQRL Devices:
I/ACORNMINER: Device 1: Acorn CLE-215+ (0050248664b04854:0000001c) Running Zen Protocol Bitstream Version 0.012
I/ACORNMINER: 1 Acorns ready to mine Zen Protocol
I/ACORNMINER: Setting default clock to 175
I/ACORNMINER: Startum Config: stratum-tcp://us.zenprotocolpool.com:8811 zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss.Miner01
I/ACORNMINER: Starting Stratum Connection to us.zenprotocolpool.com on port 8811
I/AcornWorker01: Starting...
I/ACORNMINER: Using Account: zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss
I/ACORNMINER: Workername: Miner01
I/ACORNMINER: Stratum state AcornMinerStratumStateIdle -> AcornMinerStratumStateIdle
I/ACORNMINER: Stratum state AcornMinerStratumStateIdle -> AcornMinerStratumStateConnecting
I/ACORNMINER: Stratum connected
I/ACORNMINER: Stratum state AcornMinerStratumStateConnecting -> AcornMinerStratumStateAuthorizing
I/SQJSONRPC: Sending {"jsonrpc":"2.0","id":3,"method":"mining.authorize","params":["zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss.Miner01"]}
I/SQJSONRPC: Received Message: {"id":3,"result":true,"error":null}
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Stratum state AcornMinerStratumStateAuthorizing -> AcornMinerStratumStateAuthorized
I/ACORNMINER: Stratum state AcornMinerStratumStateAuthorized -> AcornMinerStratumStateSubscribing
I/SQJSONRPC: Sending {"jsonrpc":"2.0","id":1,"method":"mining.subscribe"}
I/SQJSONRPC: Received Message: {"id":1,"result":[[["mining.set_difficulty","1eafb001aed0babeec1c010000000000"],["mining.notify","1eafb001aed0babeec1c010000000000"]],"1000e35e",4],"error":null}
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Stratum state AcornMinerStratumStateSubscribing -> AcornMinerStratumStateSubscribed
I/SQJSONRPC: Received Message: {"id":null,"method":"mining.set_difficulty","params":[512]}
{"id":null,"method":"mining.notify","params":["89c7","000000000000000000000c91cec06cd71c1a95d7d466997140182209f7e08f65680497e00001021d2a65c8cb95ca6cc48494fd429174948074dd0d1998a300d8897ba802d9e6428400000167f6e885641a195d8c2978e9741000e35e0000000000000000","1a195d8c",false]}
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Setting difficulty to 512
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Have new job
I/AcornWorker01: HashCore clock is Locked
I/AcornWorker01: Found second hashcore, enabling
I/AcornWorker01: Updating Core Configuration
I/ACORN: New Acorn Clock is 175.01 MHz, reloading MMCM
I/AcornWorker01: Found valid nonce 080270e6
I/ACORNMINER: Share difficulty was 2767.23 - target 512
I/SQJSONRPC: Sending {"jsonrpc":"2.0","id":4,"method":"mining.submit","params":["zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss.Miner01","89c7","01000000","0","e6700208"]}
I/SQJSONRPC: Received Message: {"id":4,"result":true,"error":null}
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Share Accepted!
I/ACORNMINER: A-1(01000200): Temp: 56.97 C, VCCINT: 0.88 V, Shares(F/A/I/R/L): 1/1/0/0/0, Clk: 175.00 MHz, Core Hashrate: 350.00 MH/s
I/ACORNMINER: Total Hashrate: 350.00 MH/s
I/ACORNMINER: A-1(2e79639a): Temp: 58.32 C, VCCINT: 0.88 V, Shares(F/A/I/R/L): 1/1/0/0/0, Clk: 175.00 MHz, Core Hashrate: 350.00 MH/s
I/ACORNMINER: Total Hashrate: 350.00 MH/s
I/AcornWorker01: Found valid nonce 1afadbc2
I/ACORNMINER: Share difficulty was 1292.15 - target 512
I/SQJSONRPC: Sending {"jsonrpc":"2.0","id":4,"method":"mining.submit","params":["zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss.Miner01","89c7","2e7938c2","0","c2dbfa1a"]}
I/SQJSONRPC: Received Message: {"id":4,"result":true,"error":null}


after 10 or more mins

I/ACORNMINER: Total Hashrate: 350.00 MH/s
I/ACORNMINER: A-1(20252125): Temp: 60.78 C, VCCINT: 0.86 V, Shares(F/A/I/R/L): 148/40/67/0/41, Clk: 175.00 MHz, Core Has
This is when I haven't messed with the speed. if I adjust the speed the invalid shares go up.

I've tried the other suggestions that people put forward aswell and it hasn't made any difference but anyway Thanks to the people who have replied to my posts I appreciate your help cheers!

Anyone got any other suggestions?
 

Mubarak1961

Newcomer
Member
Joined
Dec 27, 2018
Messages
8
Likes
0
#78
Lower the MH setting to 155 or so reboot and give it a go.
work with me. thanks . 6:30pm start right
Lower the MH setting to 155 or so reboot and give it a go.
AcornMiner.exe us.zenprotocolpool.com 8811 zen1q8p03x7u9qd6vjfrx0emd54r07zkquhe9yg86j823umz9e9e2yhgqhhz5gn AcornMiner2 noreply@test.com 155
In this video, I will show you guys how to download ZenProtocol wallet and set it up, then download the miner as well as set it up.
ZenProtocol is a new cryptocurrency coin 2018.
ZenProtocol uses Algorithm: SHA-3.

The GPUs used in the video = Nvidia Tesla V-100
Links:
Pool. https://zp.leafpool.com/
Miner: https://github.com/ZenProtocol-Pool/c...
Wallet: https://www.zenprotocol.com/
It looks great now after 3 hours of testing Acorns 215+ & 101, and several GPU & CPU miners at same time
https://www.zenprotocolpool.com/
https://github.com/ZenProtocol-Pool/ccminer-zp/releases/tag/8.23
 

Attachments

Last edited:

Puckboy

Newcomer
Member
Joined
Dec 3, 2018
Messages
6
Likes
2
#82
I'm only running 1 Acorn on the systems that I've tried Acorns on. I have unplugged all risers and had just the Acorn running on it's own on 3 systems now. I tried a different address and pool same problem.

Things I tried are:

The Acorn has been tested on a different motherboard this time a Celeron 1840t, MSI gaming 5 z97, 8gb 1333 ram, 2x 120sata drives 7 RX Vega 56 MSI airboost gcards, usually mining Ethereum, Monero or other cryptonote based algos.
on this system the problem is much worse I hardly get any valid shares if I adjust the clock speed (note the results are slightly better if I don't touch the speed + or - and no matter what speed I run the Acorn at the voltage never goes above 0.97v even at 100 MHz or lower. Using the default in the batch file it starts mining at 0.86v bear in mind that this a different PSU. It leads me to think there maybe a problem with the VRM on the Acorn as the voltages are all over the place for the Acorn on this system. I hooked up a power meter to the PSU to see if it was overloaded I'm drawing 1387w average when mining Ethereum with the acorn running 1455w when mining Monero. The power supply is 2000w on the 12v rail 100w on the 3.3v rail and 100w combined on all the other rails that said it's overall rating is 2000w. If I run the Acorn without any other programs running the power draw is 312w on the whole system but the voltage is still low on the Acorn.
I changed the PSU to 2x Antec HCP1300 PSU same problem although the voltages where higher but still with invalid shares.


C:\Users\Dragon Logic\Desktop\AcornMinerWin_Alpha_012c (1)>AcornMiner.exe us.zenprotocolpool.com 8811 zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss Miner01 not posting my email address @ online 175
I/ACORNMINER: Started Winsock!
I/LOGGER: Log level set to Info
I/ACORNMINER: Starting AcornMiner v0.12c
I/ACORNMINER: Scanning for Acorns...
I/ACORNMINER: Found 1 SQRL Devices:
I/ACORNMINER: Device 1: Acorn CLE-215+ (0050248664b04854:0000001c) Running Zen Protocol Bitstream Version 0.012
I/ACORNMINER: 1 Acorns ready to mine Zen Protocol
I/ACORNMINER: Setting default clock to 175
I/ACORNMINER: Startum Config: stratum-tcp://us.zenprotocolpool.com:8811 zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss.Miner01
I/ACORNMINER: Starting Stratum Connection to us.zenprotocolpool.com on port 8811
I/AcornWorker01: Starting...
I/ACORNMINER: Using Account: zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss
I/ACORNMINER: Workername: Miner01
I/ACORNMINER: Stratum state AcornMinerStratumStateIdle -> AcornMinerStratumStateIdle
I/ACORNMINER: Stratum state AcornMinerStratumStateIdle -> AcornMinerStratumStateConnecting
I/ACORNMINER: Stratum connected
I/ACORNMINER: Stratum state AcornMinerStratumStateConnecting -> AcornMinerStratumStateAuthorizing
I/SQJSONRPC: Sending {"jsonrpc":"2.0","id":3,"method":"mining.authorize","params":["zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss.Miner01"]}
I/SQJSONRPC: Received Message: {"id":3,"result":true,"error":null}
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Stratum state AcornMinerStratumStateAuthorizing -> AcornMinerStratumStateAuthorized
I/ACORNMINER: Stratum state AcornMinerStratumStateAuthorized -> AcornMinerStratumStateSubscribing
I/SQJSONRPC: Sending {"jsonrpc":"2.0","id":1,"method":"mining.subscribe"}
I/SQJSONRPC: Received Message: {"id":1,"result":[[["mining.set_difficulty","1eafb001aed0babeec1c010000000000"],["mining.notify","1eafb001aed0babeec1c010000000000"]],"1000e35e",4],"error":null}
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Stratum state AcornMinerStratumStateSubscribing -> AcornMinerStratumStateSubscribed
I/SQJSONRPC: Received Message: {"id":null,"method":"mining.set_difficulty","params":[512]}
{"id":null,"method":"mining.notify","params":["89c7","000000000000000000000c91cec06cd71c1a95d7d466997140182209f7e08f65680497e00001021d2a65c8cb95ca6cc48494fd429174948074dd0d1998a300d8897ba802d9e6428400000167f6e885641a195d8c2978e9741000e35e0000000000000000","1a195d8c",false]}
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Setting difficulty to 512
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Have new job
I/AcornWorker01: HashCore clock is Locked
I/AcornWorker01: Found second hashcore, enabling
I/AcornWorker01: Updating Core Configuration
I/ACORN: New Acorn Clock is 175.01 MHz, reloading MMCM
I/AcornWorker01: Found valid nonce 080270e6
I/ACORNMINER: Share difficulty was 2767.23 - target 512
I/SQJSONRPC: Sending {"jsonrpc":"2.0","id":4,"method":"mining.submit","params":["zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss.Miner01","89c7","01000000","0","e6700208"]}
I/SQJSONRPC: Received Message: {"id":4,"result":true,"error":null}
I/ACORNMINER: Stratum Message Received
I/ACORNMINER: Share Accepted!
I/ACORNMINER: A-1(01000200): Temp: 56.97 C, VCCINT: 0.88 V, Shares(F/A/I/R/L): 1/1/0/0/0, Clk: 175.00 MHz, Core Hashrate: 350.00 MH/s
I/ACORNMINER: Total Hashrate: 350.00 MH/s
I/ACORNMINER: A-1(2e79639a): Temp: 58.32 C, VCCINT: 0.88 V, Shares(F/A/I/R/L): 1/1/0/0/0, Clk: 175.00 MHz, Core Hashrate: 350.00 MH/s
I/ACORNMINER: Total Hashrate: 350.00 MH/s
I/AcornWorker01: Found valid nonce 1afadbc2
I/ACORNMINER: Share difficulty was 1292.15 - target 512
I/SQJSONRPC: Sending {"jsonrpc":"2.0","id":4,"method":"mining.submit","params":["zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss.Miner01","89c7","2e7938c2","0","c2dbfa1a"]}
I/SQJSONRPC: Received Message: {"id":4,"result":true,"error":null}


after 10 or more mins

I/ACORNMINER: Total Hashrate: 350.00 MH/s
I/ACORNMINER: A-1(20252125): Temp: 60.78 C, VCCINT: 0.86 V, Shares(F/A/I/R/L): 148/40/67/0/41, Clk: 175.00 MHz, Core Has
This is when I haven't messed with the speed. if I adjust the speed the invalid shares go up.

I've tried the other suggestions that people put forward aswell and it hasn't made any difference but anyway Thanks to the people who have replied to my posts I appreciate your help cheers!

Anyone got any other suggestions?
Try This:
AcornMiner.exe us.zenprotocolpool.com 8811 zen1qtm7lycqxsw798cvw5atv974muwamphjhzk85thx5rqapm07e7j9sczdkss Minor01 noreply@test.com 160

I think the email is the password for the pool!
 

Mubarak1961

Newcomer
Member
Joined
Dec 27, 2018
Messages
8
Likes
0
#83
work with me. thanks . 6:30pm start right

AcornMiner.exe us.zenprotocolpool.com 8811 zen1q8p03x7u9qd6vjfrx0emd54r07zkquhe9yg86j823umz9e9e2yhgqhhz5gn AcornMiner2 noreply@test.com 155
In this video, I will show you guys how to download ZenProtocol wallet and set it up, then download the miner as well as set it up.
ZenProtocol is a new cryptocurrency coin 2018.
ZenProtocol uses Algorithm: SHA-3.

The GPUs used in the video = Nvidia Tesla V-100
Links:
Pool. https://zp.leafpool.com/
Miner: https://github.com/ZenProtocol-Pool/c...
Wallet: https://www.zenprotocol.com/
It looks great now after 3 hours of testing Acorns 215+ & 101, and several GPU & CPU miners at same time
https://www.zenprotocolpool.com/
https://github.com/ZenProtocol-Pool/ccminer-zp/releases/tag/8.23
https://github.com/zpminer/zpminer/releases
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
zpminer.exe zen1q8p03x7u9qd6vjfrx0emd54r07zkquhe9yg86j823umz9e9e2yhgqhhz5gn.Mubarak1961/mbd656@hotmail.com u=stratum+tcp://zp-asia.leafpool.com:8811 for multi-GPU 8822
https://github.com/zpminer/zpminer/releases
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
zpminer.exe zen1q8p03x7u9qd6vjfrx0emd54r07zkquhe9yg86j823umz9e9e2yhgqhhz5gn.Mubarak1961/mbd656@hotmail.com u=stratum+tcp://zp-asia.leafpool.com:8811 for multi-GPU 8822
https://github.com/zpminer/zpminer/releases
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
zpminer.exe zen1q8p03x7u9qd6vjfrx0emd54r07zkquhe9yg86j823umz9e9e2yhgqhhz5gn.Mubarak1961/mbd656@hotmail.com u=stratum+tcp://zp-asia.leafpool.com:8811 for multi-GPU 8822

 
Last edited:

RickDangerous

Newcomer
Member
Joined
Dec 3, 2018
Messages
2
Likes
1
#84
Discord down at the moment?

I have an Acorn that keeps crashing after about 15 mins, 3 other Acorns on the System continue to work. Worked fine since I received them, started crashing today or yesterday. The only thing abnormal I can see is, it doesn't get as warm as the other acorns.
I attached a screenshot before the crash. Its about A2.
Could it be broken already?
 

Attachments

Mubarak1961

Newcomer
Member
Joined
Dec 27, 2018
Messages
8
Likes
0
#85
Hi there, try to adjust Clk to 155 in bat file as below
AcornMiner.exe us.zenprotocolpool.com 8811 zen1q8p03x7u9qd6vjfrx0emd54r07zkquhe9yg86j823umz9e9e2yhgqhhz5gn.Mubarak215+/AcornMiner2 noreply@test.com 155
 

Attachments

earlmo

Newcomer
Member
Joined
Oct 5, 2018
Messages
4
Likes
2
#86
Not sure why your temp is so low--mine is a lot warmer at a similar speed. Does it still crash if you run it with only two others?
oops.PNG
 

salvo2002

Newcomer
Member
Joined
Dec 11, 2018
Messages
4
Likes
0
#87
where can I find a list of command line options? or is it *only* how the example startup files are? it'd be nice to have a way to pass more than one pool... failovers.
 
Last edited:

Mubarak1961

Newcomer
Member
Joined
Dec 27, 2018
Messages
8
Likes
0
#88
Hi there, Zen protocol wallet just stop working, so, I go to it website and dowanload the new version, but again stop after a second from lunched. Does anyone has this issue lately?
I visted the ZP website and asked for help, there answer was as below:
There is currently maintenance work done on the system and some people have already experienced similar issues like you have mentioned. We want you to rest assure that everything is OK and should be resolved shortly. You are welcome to check back in with us in 24 hours if this persists, but it shouldn't.
 
Last edited:
Top Bottom